Heating Flat Ribbons in Silicone, Width 15 mm, Maximum Length 10m, for Electric Tracing

• Customization: Available
• Certification: RoHS, ISO9001, CE
• Type: Electric Coil
• Model NO.: 9AS
• Material: Silicon Carbide
• Form: Heating Wire
• Selling Units: Single Item
• Power Tolerance: 10%At20c
• After-Sales Service Provided: Return and Replacement
• Logo/Pattern: Laser Printing
• Plug: Euro Plug.UL Plug on Request.
• Ingress Protection: IP65
• Application: Outdoor,Commercial
• Marketing Type: Ordinary Product
• Minimum Ambient Temperature: -100c+150f
• Specification: 60X60X80cm
• Trademark: JPCI
• Origin: China
• HS Code: 8516799000
• Production Capacity: 50000

Product Description

 

Type 9AS Heating flat ribbons in silicone, width 15 mm, maximum length 10m, for electric tracing. Without thermostats.

Product Description

Main Features

 

Silicone rubber ribbons are made of fiberglass reinforced laminated silicone rubber sheets, vulcanized together through heat and high pressure on both sides of an embedded specially formed heating wire element. Fiberglass reinforced silicone rubber gives the heater dimensional stability without sacrificing flexibility. Silicone is used because of its high temperature resistance (Permanent temperature up to 200°C /390°F), high thermal conductivity (~7 10-4W/cm.K) and good electrical insulation properties (~12KV/mm)
This series is distinguished by its small width allowing it to be wound around pipes for electrical tracing applications. Heating elements of this series can be made with constant power when the temperature rise, or with positive temperature coefficient reducing the power when the temperature rises.
Other general particularities of these heaters are:
- Not affected by vibration or flexing,
- Lightweight,
- Comply with UL94-VO (flame retardant) and ROHS,
- Low smoke and low Toxicity,
- Silicone is non-toxic, and moisture and chemical resistant,
- Very thin profile

 

 

Main Applications

Some typical applications examples are: 

Provide process temperature maintenance or avoid freezing to metallic and plastic piping, gutters, valves, pumps, water meters. These ribbons are usually wrapped around the pipe or equipment, but can also be mounted longitudinally. Unlike self-regulating heating cords using PTC plastic compounds, they are not subject to a drift in their characteristics over time, and they exist in a wider surface power range.

 

 

Technical Features

Clamping: Installation is usually done on pipes, with fiberglass reinforced tape, or using adhesive heater.
Length (Dimension A): 2.5m, 5m, 10m
Width: 15mm

Silicone foil minimum bending radius : 3.2 mm (0.125") 
Ingress protection: IP65.
Minimum ambient temperature: -10 (+15)
Voltage: 220-240VAC.
Power tolerance: ±10% at 20°C
Temperature control: No thermostat or high limit switch available on these products (Width is not enough for them). K thermocouple sensor can be embedded on request and then allows electronic temperature control. For simple applications in antifreeze applications, it is also possible to use a waterproof fixed setting thermostat control box type Y22. (See accessories in the last section of this catalogue).
Power density:
from 0.1W/cm² (0.65W/inch²) to 0.8W/cm² (5.2 W/inch²). See part numbers table.
Don't use power density higher than 0.2W/cm² on plastic walls. Check the surface temperature rise versus surface power density. (Table is available in the technical introduction).
Thickness of the flexible silicone foil: 1.6 or 2.5mm

Quality control routine tests : Each element is 100% tested for continuity, resistance and insulation. Tests are made  according to EN 60335-1 and EN 50106 standards. See technical introduction. 
Dielectric Strength: 1750V AC.
Insulation resistance: ≥ 10 Megohms.
Operating temperature:
The temperature of the heated product is generally much lower than that of the surface and depends mainly on the surface power (W/cm²), the quality of the thermal contact, the viscosity, heat capacity and thermal conductivity of the heated product, the good positioning of the heater, the ambient temperature , and the fluid speed inside the pipe.
You can find in the technical introduction examples of the temperatures reached by silicone rubber heaters. They represent the temperature that may reach the heating element if it is not correctly installed.

Connection:
- 2 AWG18 or 0.75mm² FEP insulated wires, length 500mm (other lengths on request).
- 2 x AWG 18 or 2 x 0.75mm² cord with euro plug or UL plug (2 prongs).
Options:
- Power supply 110/115V
- Grounded mesh wire shield layer

 

Safety standards: 

The heaters have been designed in compliance with EEC Low Voltage Directive (LVD) 2006/95/EC and EMC directive 2004/108/EC. They must be installed in accordance with all local applicable instructions, codes, and regulations.

Packing&Shipping

Option : By air & By sea & By truck

Company Introduction

Company profile:

Established in China since 2000, with French technology and investment, our company is proud to have more than 60 years experience in manufacturing electromechanical components and 30 years experience in manufacturing safety component for Spas, swimming pools and hot tubs. This experience, combined with high tech equipment and high tech raw materials let us develop the new components needed by rapid expansion of Asian and Chinese market.
In our new factory, on more than 8000 square meters production lines, we have two manufacturing divisions:
Division one is producing components:
Thermostats, energy regulators pressure switches, level switches, flow switches, fire detection fusible links, heating elements and ceramic connection blocks.
Division two is producing complete assemblies and sub assemblies on customer specifications:

Swimming pools heaters, heat pumps backup heaters, spas heaters, small water heaters, immersion heaters, aluminum foils heaters, baseboard and convection heaters sub assemblies
Our R&D team develops new products upon customer specification, taking care of international safety standard (UL, CE, etc.).
We produce our own stamping, bending, plastic injection, zinc alloy injection, and machining.
We are equipped with up to date automatic and CNC TIG welding and laser welding equipment and ultrasonic welding checking.
We have our own climatic room, corrosion testing loops, salt spray testing, and more than 30 specific equipments for products life testing.
Our income quality control laboratory is equipped to check raw material (plastics, metals) physical characteristics and dimensions.
Our finished product control laboratory has more than 200 machines to calibrate and check temperature, pressure, level and flow controls.
From the raw material to the finished product we control every production step. Meet your control equipment demand rapidly and safely is our consistent promises.

Basic Information

Product/Service Sell: Flow switches, level switch,pressure switch, thermostat,heating elements, back up heaters for heat pumps

Number of Employees:200 to 300 People
Main Markets:North America/South America/Eastern Europe/Southeast Asia/Africa/Oceania/Mid East/Eastern Asia/Western/Europe/Northern Europe/Southern Europe/Domestic Market

Total Annual Sales Volume: US$2.5 Million - US$5 Million